Cables are one or more wires covered in a plastic covering which allows transmission of power or data between the devices. Generally, a Cable is a one or more wires covered in a plastic covering and allows transmission of power or data between the devices. The cables usually consist of a number of wires, mainly of copper or aluminum, twisted together in concentric layers. The copper or aluminium wires are used because of the high electrical conductivity, while the twisted wires give the cable flexibility. The terms wire and cables are used to describe the same components, but they are quite different. The Wire is a single electrical conductor used for the transmission of electricity or electric signals.

We provide earthing & lightning protection components such as Grounding Copper Rods, Busbars, Copper Tapes, Earth Conductors, Lightning Arrestors, Air Terminals, Earthing Grid, DC Tapes, DC Clamps, Servit Post connectors, Ground connectors, Earth Pit, Electrical Gloves 5 kv to 33 kv.

Our earthing & lightning protection solutions provides you:                          

* Low installed costs through intelligent design.

* Increased safety with code compliant products.

* Design services support and technical advice.

* Reliable & high quality manufactured components.

To meet the criteria for the explosion-proof rating, an enclosure must be able to contain any explosion originating within its housing and prevent sparks from within its housing from igniting vapors, gases, dust, or fibers in the air surrounding it. Therefore, explosion proof, when referring to electrical enclosures, does not mean that it is able to withstand an exterior explosion. Instead, it is the enclosures ability to prevent an internal spark or explosion from causing a much larger blast. The equipment must meet the temperature requirements of the specific application in which it is to be installed. This means that the operating temperature of the motor (and its enclosure) or another component cannot be greater than the lowest ignition/combustion temperature of the gases or dust in the atmosphere where the component is to be installed. Some refineries and processing facilities operate in cooler environments. Because of the often cooler ambient temperatures, heat is often required in these applications. However, typical open coil heaters cannot be used in hazardous areas due to the explosion hazard. For these applications, explosion proof fin tube heaters must be utilized. Explosion proof heaters incorporate fin tube heating elements and enclosed electrical connections to meet code and reduce surface temperatures.

Strut Channel is a standardized formed structural system used in the construction and electrical industries for light structural support, often for supporting wiring, plumbing, or mechanical components such as air conditioning or ventilation systems.  A strut is usually formed from a metal sheet, folded over into an open channel shape with inward-curving lips to provide additional stiffness and as a location to mount interconnecting components. Increasingly, struts are being constructed from fiberglass, a highly corrosion-resistant material that’s known for its lightweight strength and rigidity. Struts usually have holes of some sort in the base, to facilitate interconnection or fastening strut to underlying building structures.  The main advantage of strut channels in construction is that there are many options available for rapidly and easily connecting lengths together and other items to the strut channel, using various specialized strut-specific fasteners and bolts.

Conduit Fittings are the connectors and fittings used for connecting one piece of conduit to another, or to connect conduit to an electric box. The conduit fittings are available in various metals, with different levels of moisture protection. The conduit fittings are used in power generation, food processing, robotics, wastewater treatment, infrastructure, mining etc.

The conduit & fittings offer the solution for:

* Extreme temperature protection.

* Corrosive & harsh environment protection.

* Liquid ingress protection.

* Explosive environment protection.

* Continuous operation.

* Reduced installation time & cost.

Cable Rollers are used so that when the cable is being pulled, it runs along the roller and not on the ground. Cable rollers should always be used when pulling cables. Cable rollers are used to support and guide LV, MV & HV cables into open trenches without damaging cable sheaths and incurring over-bending stresses on power cables, typically at 11kV/33kV. Cable pulling compound is also known as cable gel or cable lube is specially designed lubricants to assist in reducing friction when pulling or hauling cables through conduit, ducts or PVC pipes. A Cable Pulling Winches are powered by a motor which is maneuvered by diesel and comprises of a storage drum which is fitted by non-spin wire ropes. It can be operated by a single person with the help of rollers, swivels and pulling socks. All the components are manufactured in-house and ensure the best quality for the customers. The winches are finished with standard paints or are galvanized and powder coated. Cable Pulling Winch is used for pulling power cables, Heavy pipes, etc.. It is used to lay the power cables in the trench. There are many variants in Cable Pulling Winch for different sizes on Power Cables. These Cable Pulling Winches are high-quality products and represent the latest modern technical standard in the field of cable pulling winches.

A cable gland is a device designed to attach and secure the end of an electrical cable to the equipment. A cable gland provides strain-relief and connects by a means suitable for the type and description of cable for which it is designed—including provision for making electrical connection to the armor or braid and lead or aluminum sheath of the cable if any. Cable glands may also be used for sealing cables passing through bulkheads or gland plates. Cable glands are mechanical cable entry devices. They are used throughout a number of industries in conjunction with cable and wiring used in electrical instrumentation and automation systems. Cable glands may be used on all types of electrical power, control, instrumentation, data, and telecommunications cables. They are used as a sealing and termination device to ensure that the characteristics of the enclosure which the cable enters can be maintained adequately. Cable glands are devices that are critical when terminating cables in hazardous or harsh environments, where ingress protection, sealing, and grounding is necessary to safely pass a cable, wire or tube through an enclosure.

1. Conduit pipes are used for conveying fluids or for protecting electric cables. In these pipes, networks are laid within the boundaries of a facility not to transfer any fluid but to protect the electrical and optical fibres & cables from an external environment.We provide a superior range of conduit pipes to customers with salient features.

Main features of our conduit pipes are:

* High resistance to oil.

* No deformation or bending.

* High insulation resistance.

* No cracking.

* Excellent rigidity.

* Rigid Steel conduit (HDG), IMC, EMT, PVC Coated.

* Size ½” to 6”

Cadweld exothermic process is a system in which the materials from other manufacturers should not be mixed or matched with Cadweld molds or welding materials. The Cadweld process is a method of making electrical connections of copper-to-copper or copper-to-steel in which no outside source of heat or power is required. In this process, conductors are prepared and placed in a purpose-designed graphite mold, and exothermically welded to produce a permanent electrical connection.

The main advantages of the Cadweld process are that it:

• Will resist repeated faulty currents.
• Will not deteriorate with age.
• Eliminates any risk of loosening or corrosion due to its molecular bonding characteristics.
• Offers the lowest possible earth path resistance.
• By visual inspection can be quality controlled.